APRS Track Direct

My position About ☰

reset

VK2LJ-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2LJ-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Temp*
1732334180	13.3 Volts	41.77 Deg.C
1732333880	13.39 Volts	41.77 Deg.C
1732333580	13.33 Volts	41.77 Deg.C
1732333281	13.39 Volts	41.77 Deg.C
1732332981	13.33 Volts	41.77 Deg.C
1732332681	13.33 Volts	41.77 Deg.C
1732332381	13.33 Volts	41.28 Deg.C
1732332080	13.3 Volts	41.28 Deg.C
1732331780	13.36 Volts	41.28 Deg.C
1732331481	13.36 Volts	40.79 Deg.C
1732331181	13.39 Volts	40.79 Deg.C
1732330881	13.36 Volts	40.79 Deg.C
1732330582	13.33 Volts	40.79 Deg.C
1732330282	13.3 Volts	40.79 Deg.C
1732329983	13.39 Volts	40.3 Deg.C
1732329681	13.33 Volts	39.81 Deg.C
1732329382	13.3 Volts	39.81 Deg.C
1732329082	13.24 Volts	39.81 Deg.C
1732328783	13.27 Volts	39.32 Deg.C
1732328483	13.27 Volts	39.32 Deg.C
1732328184	13.27 Volts	39.32 Deg.C
1732327884	13.3 Volts	39.32 Deg.C
1732327584	13.3 Volts	39.32 Deg.C
1732327283	13.27 Volts	38.83 Deg.C
1732326984	13.3 Volts	38.83 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)