APRS Track Direct

My position About ☰

reset

KA6PRW-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KA6PRW-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Battery*	Temp*
1732386512	13.6 Volts	18.78 Deg.C
1732386482	13.68 Volts	18.78 Deg.C
1732386469	13.74 Volts	18.78 Deg.C
1732386455	13.77 Volts	18.29 Deg.C
1732386430	13.8 Volts	18.29 Deg.C
1732386326	13.86 Volts	17.81 Deg.C
1732386212	13.71 Volts	17.32 Deg.C
1732386175	13.71 Volts	16.83 Deg.C
1732386075	13.62 Volts	15.85 Deg.C
1732386060	13.62 Volts	15.85 Deg.C
1732385994	13.62 Volts	14.87 Deg.C
1732385839	13.71 Volts	13.4 Deg.C
1732385792	13.77 Volts	12.43 Deg.C
1732384377	13.62 Volts	16.34 Deg.C
1732384192	13.71 Volts	15.36 Deg.C
1732384092	13.39 Volts	14.87 Deg.C
1732383982	13.62 Volts	14.38 Deg.C
1732383815	13.68 Volts	12.92 Deg.C
1732383729	13.57 Volts	11.94 Deg.C
1732383697	13.71 Volts	11.45 Deg.C
1732383684	13.68 Volts	10.96 Deg.C
1732383648	13.65 Volts	10.96 Deg.C
1732383629	13.62 Volts	10.47 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)