This is the latest recevied telemetry packets stored in our database for station/object WE6Z. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time | Value1* | Value2* | Value3* | Value4* | Value5* |
---|---|---|---|---|---|
1732318114 | 481 | 604 | 0 | 0 | 0 |
1732317994 | 481 | 603 | 0 | 0 | 0 |
1732317875 | 479 | 602 | 0 | 0 | 0 |
1732317755 | 475 | 601 | 0 | 0 | 0 |
1732317517 | 477 | 600 | 0 | 0 | 0 |
1732316920 | 401 | 598 | 0 | 0 | 0 |
1732316800 | 401 | 598 | 0 | 0 | 0 |
1732316442 | 401 | 598 | 0 | 0 | 0 |
1732316203 | 401 | 598 | 0 | 0 | 0 |
1732315727 | 401 | 598 | 0 | 0 | 0 |
1732315487 | 401 | 598 | 0 | 0 | 0 |
1732315368 | 401 | 598 | 0 | 0 | 0 |
1732315010 | 402 | 598 | 0 | 0 | 0 |
1732314770 | 402 | 598 | 0 | 0 | 0 |
1732314652 | 402 | 598 | 0 | 0 | 0 |
1732314413 | 402 | 598 | 0 | 0 | 0 |
1732314174 | 402 | 597 | 0 | 0 | 0 |
1732314054 | 401 | 598 | 0 | 0 | 0 |
1732313816 | 402 | 598 | 0 | 0 | 0 |
1732313577 | 402 | 597 | 0 | 0 | 0 |
1732313339 | 402 | 597 | 0 | 0 | 0 |
1732313219 | 402 | 598 | 0 | 0 | 0 |
1732313100 | 402 | 598 | 0 | 0 | 0 |
1732312980 | 401 | 598 | 0 | 0 | 0 |
1732311547 | 402 | 597 | 0 | 0 | 0 |
*Used Equation Coefficients:
Value1: 0, 1, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)