APRS Track Direct

My position About ☰

reset

2E0XLS-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 2E0XLS-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Temp*
1732263370	12.34 Volts	11.45 Deg.C
1732263191	12.36 Volts	11.94 Deg.C
1732263010	12.72 Volts	11.94 Deg.C
1732262830	12.72 Volts	11.94 Deg.C
1732262649	12.72 Volts	11.94 Deg.C
1732262289	12.69 Volts	11.94 Deg.C
1732262109	12.69 Volts	11.94 Deg.C
1732261928	12.72 Volts	11.94 Deg.C
1732261747	12.69 Volts	11.94 Deg.C
1732261568	12.69 Volts	12.43 Deg.C
1732261207	12.63 Volts	12.43 Deg.C
1732261026	12.66 Volts	11.94 Deg.C
1732260847	12.54 Volts	12.43 Deg.C
1732260666	12.51 Volts	12.43 Deg.C
1732260486	12.66 Volts	12.92 Deg.C
1732260306	12.66 Volts	12.43 Deg.C
1732260124	12.48 Volts	12.92 Deg.C
1732259945	12.75 Volts	12.92 Deg.C
1732259764	12.75 Volts	12.92 Deg.C
1732259584	12.66 Volts	13.4 Deg.C
1732259403	12.75 Volts	13.89 Deg.C
1732259224	12.72 Volts	14.38 Deg.C
1732258857	17.08 Volts	18.29 Deg.C
1732258834	14.01 Volts	17.81 Deg.C
1732258821	14.24 Volts	17.81 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)